欢迎来到济南美德森服饰官方网站! 加入收藏 在线留言 职业装定制
济南职业装
全国服务热线 : 0531-85980985
您现在的位置 : 首页 > 资讯中心 > 常见问题 >
园服展示
GARDEN SHOW
更多园服款式
欢迎咨询
0531-85980985
专业设计师一对一定制
幼儿园园服的的检验内容和检验细则
发布人:admin发布时间:2022-08-22 11:35:25

幼儿园园服检验内容与检验要求如下:
The inspection contents and requirements of kindergarten uniforms are as follows:
1、产品面料和里料
1. Product fabric and lining
①各类校服的面料、里料、辅料洗涤后均不可褪色:质地(成分、手感、光泽、织物组织等)、图案及绣花(位置、面积)应与要求相符;
① The fabrics, linings and accessories of various school uniforms shall not fade after washing: the texture (composition, feel, luster, fabric organization, etc.), pattern and embroidery (position and area) shall meet the requirements;
②各类校服成品的面料不能有纬斜的现象;
② The finished fabrics of various school uniforms shall not have weft skew;
③各类校服成品的面、里、辅料不能有扒丝、破损、破洞或影响穿着效果的严重织残(粗纱、缺纱、线结等)和布边针孔;
③ The surface, lining and auxiliary materials of all kinds of school uniforms shall be free of silk, damage, holes or serious fabric defects (roving, missing yarn, knot, etc.) and cloth edge pinholes that affect the wearing effect;
⑤凡针织类校服不能有表面织纹凹凸不平的现象,且衣物表面不能有纱线接头;
⑤ All knitted school uniforms shall not have uneven surface texture, and the surface of the clothes shall not have yarn joints;
⑥各类校服的面、里、辅料不能有油渍、笔渍、锈渍、色渍、水印、胶印、划粉印等各类污渍;
⑥ The surface, lining and auxiliary materials of all kinds of school uniforms shall be free of oil, pen, rust, color, watermark, offset and powder printing;
⑦色差
⑦ Chromatic aberration
A、同一件衣服的不同衣片之间不能存在同种颜色不同深浅的现象;
A. The phenomenon of different shades of the same color cannot exist between different pieces of the same garment;
B、同一件衣服的同一衣片上不能存在严重染色不均匀的现象(款式面料设计要求除外)
B. There shall be no serious uneven dyeing on the same piece of the same garment (except for the design requirements of style and fabric)
C、同款校服的同种颜色之间不能有明显色差;
C. There shall be no obvious color difference between the same colors of the same school uniform;
D、上下装分开的套装,上装和与之配套的下装之间不能有明显的色差;
D. The upper and lower suits shall be separated, and there shall be no obvious color difference between the upper suit and the matching lower suit;
⑧凡水洗、磨洗及喷砂的面料应手感柔软、色泽正确、图案对称,且对面料没有损坏(特殊设计除外);
⑧ All washed, abraded and sandblasted fabrics shall be soft in hand, correct in color, symmetrical in pattern, and free from damage to fabrics (except for special design);
⑨凡有涂层的面料均需涂层均匀、牢固,表面不能有残痕。成品洗涤后不能有涂层起泡、脱落现象。
⑨ All coated fabrics shall be coated evenly and firmly without residual marks on the surface. The finished product shall be free of blistering and peeling after washing.
2、产品尺寸
2. Product size:
①成品各部位尺寸与要求的规格尺寸相符,误差不能超出公差范围;
① The dimension of each part of the finished product shall be consistent with the required specification and the error shall not exceed the tolerance range;
②各部位的测量方法严格按要求。
② The measurement method of each part shall be in strict accordance with the requirements.
3、产品工艺
3. Product process
①粘衬
① Adhesive lining
A、凡用衬部位均需选择与面、里料材质、颜色、缩率相适应的衬;
A. All lining parts shall be lined with the materials, colors and shrinkage of the surface and lining;
B、各粘衬部位要粘合牢固、平整,不能有渗胶、起泡现象,不能引起面料皱缩。
B. The lining parts shall be firmly bonded and flat, and there shall be no glue leakage and foaming, and the fabric shall not shrink.
②车缝工艺
② Sewing process
A、缝纫线的种类和验色应与面、里料的颜色和质地相衬,钉扣线应与扣子的色泽相适应(特殊要求的除外);
A. The type and color inspection of sewing thread shall be consistent with the color and texture of the surface and lining, and the nail thread shall be compatible with the color of the button (except for special requirements);
B、各缝合(包括包缝)部位不能有跳针、断线、缝边脱丝或连续开线的现象;
B. There shall be no needle skipping, thread breaking, thread shedding at the sewing edge or continuous thread opening at each sewing (including over sewing);
C、各缝合(包括包缝)部位及明线处要平整,线迹的松紧要合适,不能有浮线、线套、拉伸或吃紧等影响外观的现象;
C. All sutures (including wrapping seams) and open lines shall be flat, and the tightness of the stitches shall be appropriate, and there shall be no floating thread, thread sleeve, tension or tension that may affect the appearance;
D、各明线处不能有面、底线互透的现象,特别是面底线颜色不同时;E、省缝的省尖不能开线,正面不能出包;
D. There shall be no mutual penetration between the surface and the bottom line at each open line, especially when the color of the surface and the bottom line is different; E. The dart tip of the dart seam cannot be opened, and the front side cannot be out of the bag;
F、缝合时应注意相关部位缝份的倒向,不能扭曲,翻拧的现象;
F. When sewing, pay attention to the reverse direction of the seam allowance at the relevant parts, and do not twist or twist;
G、各类校服所有打结处不能露毛;H、凡有滚条、镶边或牙子的款式,镶边和牙子的宽窄应均匀一致;I、各种标识应用顺色线缝制,且不能有毛露现象;
G. All knots of various school uniforms shall not be exposed; H. Where there are rolling strips, edging or teeth, the width of the edging and teeth shall be uniform; 1. All kinds of marks shall be sewn with color matching thread, and there shall be no hairiness;
J、凡有绣花的款式,绣花部位应线迹平整,不起泡,不吃纵,无毛露,背面的衬纸或衬布必须抠净;K、各缝份要宽窄均匀,符合要求。
J. Where there is an embroidered style, the embroidered part shall be flat, free from blistering, longitudinal, and hairy dew. The backing paper or lining cloth on the back must be clean; K. The width of each seam shall be uniform and meet the requirements.
③锁钉工
③ Nailer
A、各类服装的钉扣(包括纽扣、按扣、四件扣,挂钩,魔术贴等)要方法正确,对应准确,钉制牢固、完整无缺且没有毛露,同时注意备扣要齐全;
A. All kinds of clothing buttons (including buttons, snap buttons, four piece buttons, hooks, Velcro, etc.) shall be correct in method, accurate in correspondence, firm, complete and free of hairiness, and attention shall be paid to complete button preparation;
B、锁钉类的校服的扣眼要完整、平服、尺寸合适,不能过细,过大,过小,露白或毛露;
B. The buttonholes of school uniforms with locking nails shall be complete, flat and of appropriate size, and shall not be too thin, too large, too small, exposed white or hairy;
C、按扣和四件扣应有垫布和垫片,且面(皮)料上不能有铬痕或铬坏的现象。 ④后整理A、外观:所有服装应全身无线毛;
C. The snap fastener and four piece fastener shall be provided with pad cloth and gasket, and the surface (leather) material shall not have chromium mark or chromium damage. ④ Finishing A. appearance: all clothes shall be free of hair;
B、各类校服要熨烫平整,不能有死褶、亮光、烫痕或焦糊的现象;
B. All kinds of school uniforms should be ironed smoothly, and there should be no dead folds, bright lights, ironing marks or scorching;
C、各合缝处任一缝子的烫倒方向应整条保持一致,不能扭曲或反拧;
C. The ironing direction of any seam at each seam shall be consistent with the whole seam, and it shall not be twisted or reversed;
D、各对称部分的缝子的烫倒方向应对称;
D. The sewing direction of each symmetrical part shall be symmetrical;
E、有裤线的裤子前、后裤线需严格按要求整烫。
E. The front and rear trouser lines of trousers with trouser lines shall be ironed strictly according to the requirements.
4、产品辅料
4. Product accessories
①拉链
① Zipper
A、拉链颜色,材质正确,无脱色,变色的现象;
A. The color and material of the zipper shall be correct without discoloration and discoloration;
B、拉头结实,经得起反复拉合;
B. The slider is firm and can withstand repeated pulling;
C、齿头吻合缜密均匀,无缺齿,缺铆现象;
C. The tooth heads are closely and evenly matched without missing teeth and rivets;
D、拉合顺畅;
D. Smooth pulling and closing;
E、裙子、裤子的拉链若为普通拉链必须有自动锁。
E. If the zipper of skirt and pants is ordinary zipper, it must have automatic lock.
②扣子、四件扣、挂钩,魔术贴,腰带等配件:
② Button, four piece buckle, hook, Velcro, belt and other accessories:
A、颜色、材质正确,不脱色,变色;
A. Correct color and material, no discoloration or discoloration;
B、没有任何影响外观和使用的质量问题;
B. There are no quality problems affecting the appearance and use;
C、开合顺畅,且经得起反复开合。
C. The opening and closing are smooth and can withstand repeated opening and closing.
5、产品各种标识
5. Product identification
①主标:主标内容要求正确、完整、清晰、不能残缺不全,并缝制在正确位置。
① Main mark: the contents of the main mark shall be correct, complete, clear, incomplete and sewn in the correct position.
②尺寸标:尺寸标内容要求正确、完整、清晰、缝制牢固,号型订缝正确,且与主标颜色一致。
② Size mark: the content of the size mark shall be correct, complete, clear, firmly sewn, the size type shall be correctly sewn, and the color shall be consistent with the main mark.
③侧标或下摆标:侧标或下摆标要求正确、清晰、缝制位置正确、牢固,特别注意不能颠倒。
③ Side mark or bottom mark: the side mark or bottom mark shall be correct and clear, and the sewing position shall be correct and firm. Special attention shall be paid not to reverse.


④洗标:
④ Standard washing:
A、洗标的款式与订单一致,洗涤方式图文相符,符号和文字印刷、书写正确,缝制牢固且方向正确(服装平铺与桌面时应为印有款名的一面朝上,有阿拉伯文字的在底面);
A. The style of the washing label is consistent with the order, the washing method is consistent with the graphics and text, the symbols and words are printed and written correctly, the sewing is firm and the direction is correct (when the clothes are laid flat and on the table top, the side with the name of the item is upward, and the side with Arabic characters is on the bottom);
B、洗标的文字必须清晰,耐洗;
B. The text of the washing mark must be clear and washable;
C、同一系列的服装标不能打错。
C. The same series of clothing labels cannot be wrong.
二、中查与质量控制点服装生产的过程越复杂,流程越长需要的检验次数和质量控制点越多。一般来说在服装完成缝制工序后都要进行一次半成品检验,这个检验通常由流水线上的质检人员或者组长来进行后整理之前的质量确认,方便产品的及时修改。而对于一些品质要求较高的西装外套等校服,还会在产品的部件组合前对零部件进行质量检验和控制。如当前片上的口袋、省道、拼接等工序完成后与后片连接前要做一次检验控制;袖子、领子等部件完成后也应该在与衣身组合前做一次检验;这样的检验工作可以由组合工序的人员来做,防止有质量问题的部件流入组合加工流程。增加半成品检验和零部件质量控制点后,看起来投入了很多人力和时间的浪费,但是这样可以减少返工量、确保质量,要知道时间成本的投入是很高的。
2、 Intermediate inspection and quality control points: the more complex the garment production process, the longer the process, and the more inspection times and quality control points required. Generally speaking, a semi-finished product inspection shall be conducted after the garment sewing process is completed. This inspection is usually carried out by the quality inspection personnel or team leader on the assembly line to confirm the quality before finishing, so as to facilitate the timely modification of the products. For some school uniforms with high quality requirements, such as suits and jackets, quality inspection and control will be carried out on the parts before the assembly of the products. For example, the pocket, dart, splicing and other processes on the front sheet shall be inspected and controlled once before being connected with the back sheet; After the sleeves, collars and other parts are completed, they should also be inspected before being combined with the body; Such inspection can be performed by the personnel of the combined process to prevent the parts with quality problems from flowing into the combined processing process. After adding semi-finished product inspection and parts quality control points, it seems that a lot of manpower and time are wasted. However, this can reduce the rework amount and ensure the quality. It should be known that the time cost is very high.
三、品质改良的三个方法企业通过持续改进来提升产品质量,这是企业质量管理的重要环节。
3、 Three methods of quality improvement enterprises improve product quality through continuous improvement, which is an important part of enterprise quality management.
品质改良一般通过如下方法:1、数据分析法:通过对不合格产品质量问题统计,分析主要的产生原因,并在后期生产环节有目的的改进。如服装尺寸产生了普遍的偏大或者偏小问题,就要分析产生这样问题的原因,在后期生产中通过如样板尺寸调整、面料预缩、服装尺寸定位等方法来改善。数据分析为企业的质量改进提供了数据支撑,服装企业需要健全检验环节的数据记录,检验不仅仅是找出不合格品,然后返修,还应该为后期预防做好相应的数据积累。
The following methods are generally adopted for quality improvement: 1. Data analysis method: the main causes are analyzed through statistics on the quality problems of unqualified products, and targeted improvement is made in the later production links. If the clothing size is generally too large or too small, it is necessary to analyze the causes of such problems and improve them in the later production through such methods as template size adjustment, fabric pre shrinking, clothing size positioning, etc. Data analysis provides data support for the quality improvement of enterprises. Garment enterprises need to improve the data records of inspection links. Inspection is not only to find out unqualified products and then repair them, but also to accumulate corresponding data for later prevention.
2、观察法:通过小组长或者巡检人员的随机观察,发现质量问题及时指出,并告诉作业人员正确的操作方法及质量要求。对于新员工或这新产品上线时,这样的巡视是必不可少的,以免加工出较多需要返修的产品。
2. Observation method: through the random observation of the team leader or the patrol inspection personnel, the quality problems found shall be pointed out in time, and the operators shall be informed of the correct operation methods and quality requirements. For new employees or when the new product is launched, such inspection is essential to avoid processing more products that need to be repaired.
3、质量追溯法:用质量追溯法,让出质量问题的员工承担相应的修改和经济责任,通过这个方法提升员工的质量意识,不生产不合格品。
3. Quality Traceability Method: the quality traceability method is used to make the employees who have quality problems bear the corresponding modification and economic responsibility. Through this method, the quality awareness of the employees is improved and the unqualified products are not produced.
(1)制定安全操作规定,推刀使必须佩带防护手套;
(1) Formulate safety operation regulations, and the knife pusher must wear protective gloves;
(2)严格执行顺毛、顺色、顺光作为正面的规定;
(2) Strictly implement the provisions that the wool, color and smoothness shall be taken as the front;
(3)严格执行色差、疵点范围规定;
(3) Strictly implement the regulations on color difference and defect range;
(4)严格按工艺规定执行对条、对格规定;
(4) Strictly follow the process regulations to implement the regulations on article and grid;
(5)严格执行辅料、排料、节料、开刀、定位、编号的技术规定;
(5) Strictly implement the technical regulations on auxiliary materials, material discharge, material saving, cutting, positioning and numbering;
(6)严格执行清洁、文明生产规定,节约面料,不污染裁片。
(6) Strictly implement the regulations on clean and civilized production, save the fabric and do not pollute the cutting pieces.
以上就是为大家介绍的有关济南幼儿园园服定做的详细的介绍,希望对您有所帮助.如果您有什么疑问的话,欢迎联系我们.我们将以的态度,为您提供服务http://www.sdzzfs.com
The above is the detailed introduction about the customized kindergarten uniforms of Jinan kindergarten. I hope it will help you. If you have any questions, please contact us. We will provide services for you with our attitude http://www.sdzzfs.com

上一条 : 抱歉暂无数据

下一条 : 幼儿园园服总是皱巴巴,简单1个动作,让衣服恢复平整

本站图片均由网站所有方提供,部分图片来源于网络,如有任何疑问请及时与我们联系,未经沟通本站不承担相关法律责任!

鲁公网安备37010402000667号

 XML 站点地图 TXT